气液增压泵是根据客户的实际需要，将气液增压泵、油箱(水箱)及各部件装配在管式框架内或封闭箱体内，结构紧凑，使用方便。调压阀、压力表、阀门等均为面板安装。那么可以知道的是，订购到满意的增压泵就要知道参数及其他，下面来简单了解下。
The gas-liquid booster pump is to assemble the gas-liquid booster pump, oil tank (water tank) and various components in the tubular frame or closed box according to the actual needs of customers, with compact structure and convenient use. Pressure regulating valves, pressure gauges, valves, etc. are panel mounted. What you can know is that you need to know the parameters and others when ordering a satisfactory booster pump. Let's have a brief understanding.
驱动气体的压力和流量
Pressure and flow of driving gas
所有的泵和动力单元在连续工作时使用的驱动气压不超过0.69Mpa，在间歇工作时可达到1.03Mpa。在佳性能状态时气动泵的耗气量，请参照所需驱动气体流量表。
The driving air pressure used by all pumps and power units during continuous operation shall not exceed 0.69mpa, and can reach 1.03mpa during intermittent operation. For the air consumption of the pneumatic pump under the condition of good performance, please refer to the required driving gas flow table.
工作压力和流量
Working pressure and flow
所有的泵和动力单元的工作压力参照驱动气压为0.48Mpa时泵输出压力和流量。如果泵的大输出压力大于所需的工作压力，这就要考虑措施。对于大输出压力，请参照产品目录中的“静态下驱动气压力和输出液压近似比率表”。动力单元的选型与泵一致。对于工作流量，请参照产品目录中的“性能曲线图”。
The working pressure of all pumps and power units refers to the pump output pressure and flow when the driving air pressure is 0.48mpa. If the large output pressure of the pump is greater than the required working pressure, safety measures should be considered. For large output pressure, please refer to the "table of approximate ratio of static driving air pressure and output hydraulic pressure" in the product catalog. The type selection of power unit is consistent with that of pump. For working flow, please refer to the "performance curve" in the product catalog.
输送液体介质
Conveying liquid medium
泵输送的液体介质是泵的选型中着重考虑的部分。液压部分的材质和液压密封圈是由输送的液体介质所决定的。泵可用油、水和大多数液体介质。标准泵的主要液压密封圈是丁橡胶和聚氨酯，单向阀座采用特氟龙密封。其它密封材料包括碳氟化合物和亚乙基丙烯，这些密封材料主要用于输送的特殊介质。
The liquid medium delivered by the pump is an important part of pump selection. The material of the hydraulic part and the hydraulic seal ring are determined by the liquid medium conveyed. The pump can use oil, water and most liquid media. The main hydraulic sealing rings of the standard pump are butadiene rubber and polyurethane, and the one-way valve seat is sealed by Teflon. Other sealing materials include fluorocarbons and ethylidene propylene, which are mainly used for special media for transportation.
其它
other
箱体外表喷塑处理。各液压部位连接处密封可靠、不允许渗油，连接管道采用不锈钢材料。为用户提供维护手册和说明书。
The surface of the box is sprayed with plastic. The connections of all hydraulic parts are sealed reliably without oil leakage, and the connecting pipes are made of stainless steel. Provide users with maintenance manuals and instructions.
气液增压泵由单向阀控制的高压活塞不断的将气体排出，气液增压泵的出口压力大小与空气驱动压力有关。气液增压泵的工作介质可为水、而且可靠性高，免维护和寿命长。气液增压泵是一种柱塞式泵，工作时，增压泵迅速往复工作，随着输出压力接近设定压力值，泵的往复速度减慢直停止。此时，泵输出压力恒定，能量消耗很低，各部件停止运动。
The gas-liquid booster pump is continuously discharged by the high-pressure piston controlled by the one-way valve. The outlet pressure of the gas-liquid booster pump is related to the air driving pressure. The working medium of the gas-liquid booster pump can be water, with high reliability, maintenance free and long service life. The gas-liquid booster pump is a kind of plunger pump. When working, the booster pump quickly reciprocates. As the output pressure approaches the set pressure value, the reciprocating speed of the pump slows down until it stops. At this time, the pump output pressure is constant, the energy consumption is very low, and all parts stop moving.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.feileisi.com And consult our staff, will serve you wholeheartedly.
